Inventory Details & Specifications for 21ft Rogue Boatworks Yukon Coastal 185 Outboard Model

Rogue Boatworks Yukon Coastal 185 Outboard ModelOnly $74,888.00*IN STOCK*

Status: New
Length: 21ft
Program Year: 2018
Price: $74,888.00
Item Number: RQJT1648G718

Description & Standard Equipment:

Rogue Boatworks Coastal Yukon 185

Key Features:

• Fully Welded Seams - No Stitch Welded Hull - 40% more Strength and Integrity
• Bottom, Support Girders, Sides & Transom - 5086 Marine Aluminum Alloy
Powder Coated and Baked twice at 420° - 3 times more corrosion & impact resistant than painted boats
Proven by Law Enforcement & Government Customers
• Fully Welded D-Tube Customized Aluminum Trailer - no heavy I-Beams made of steel

5 Reasons why Rogue Jet Boats are more expensive & higher quality:

(1)The Impact of Fully Welded Seams in the Hull

There is no stitch welding in the hull all seams are fully welded resulting in about 25 to 30% more labour and 10 to 12 lbs more welding wire when welding the hull together.

Stitch/Skip welded boats loose 40% to 50% of their strength and integrity

Boats that run in rough seas with large or short interval waves are prone to cracking those stitch welds.
The open/not welded areas between the welds is where the flexing and cracking starts.
These areas are all hidden below the floor where most owners don't inspect with limited access, an area.

(2) Stronger Marine Alloy on all Parts

Rogue uses the more expensive, salt water corrosion resistant and 40% stronger 5086 Aluminum on the hull, sides, transom and box girders unlike other manufacturers who only use 5086 on the bottom and the cheaper/weaker 5052 on the sides, transom and box girders.

Rogue uses 1/4" and 3/8" plate in their transom and pod deck others use 1/8" and 3/16" at best.

(3) A Baked Finish - 3 times more resistent

The baked powder coat finish on a Rogue is 3 times more corrosion and impact resistant then painted boats and twice as durable.

The boat goes into the oven twice and gets the powder coat baked on and then a clear coat over top. The finish is the same under the gunnels, dash, seat boxes, fish and floor boxes as well as all visual areas on the top side of the boat.

(4) Rogue Trailers: Long Life Beauties

Rogue makes their own fully welded custom D-tube trailers. Customized for each boat which cost about twice as much.

They are not like the cheap aluminum I-beam trailers or steel galvanized trailers that other manufactures put under their boats.

Nothing is bolted.
The fenders are solid and fully welded. They have torsion axles, disc brakes, oversize radial tires and LED lights. The trailers go all the way to the back of the boat with full welded steps and welded side guides. The trailer on a Rogue is always way over capacity needed to make sure it has a long life.

(5) Less Maintenance Costs

The high durability of Rogue Boats in general, will keep your total cost of ownership low in the long term and the renewal of a 3M Heavy Duty Vinyl Wrap and not the decal material for the exterior sides, would cost you only 10% of a usual new painting.

The Rogue Trailers are equiped with Vault oil bath hubs - No Inspection - No Maintenance - No Service required.

The Coastal Outboard Series are designed to handle the rough stuff

Built extra deep and wide with extra freeboard , these outboard powered Deep Vees from Rogue have been designed for the roughest conditions on rivers, lakes, bays and the ocean.

Safety in high sides (36") and the extra wide bottom (78") for more stability makes the "Coastal" one of the safest and most seaworthy all welded aluminum boats in the industry.

The progressive deadrise of the boats bottom - from 50 degrees at the bow to 18 degrees at the transom - makes for a smooth ride in choppy seas.

• Hull Length: 18.5'
• Hull Length overall (Bracket and Transom included, without Outboard): 21'
• Beam: 102"
• Side Height: 36"
• Bottom Width: 78"
• Deadrise: Bow 50º / 18º Transom
• Fuel Capacity: 40 Gallon
• Standard Power
• 4 lifting/turning strakes
• Side Thickness: 0.125"
• Bottom Thickness: 0.190"
• Transom Thickness: 0.190"
• Box Girder Thickness: 0.160"

Standard Features:
• Extended outboard bracket-full width
5086 Marine Alumninum Alloy at Sides, Bottom, Transom, Decks and Support Girders
• 2 panoramic windshield wipers
• Welded downrigger mounts (2)
• Navigation Lights
2 Heavy Duty marine batteries + Switch
• Bilge Pump and auto switch 1100 gph
• Non slip grip steering wheel
• Locking glove box with grab handle
• Water Separator
• 12 volt Power Point
• Bow rope guide with jam cleat
• 5 welded cleats (8 inch)
• Diamond Plate (step deck, trim, fore deck)
• Bow storage compartment
• Zinc anode on transom
• Anchor door in bow step deck 23"X26"
• Horn
• Transducer bracket
• 4 heavy duty lifting/turning strakes
• Paint all diamond plate
• Extended additional rod grippers above side trays
• Full fill from port side by windshield
• Additional transom storage under transom fish box • Floor board cut outs at transom for draining debris
• Powder on bow step deck, box lids, & transom outboard bracket
• Switch panel for accessories, wipers, horn, bilge pump
• Suspension Seats
• Rear seats with hinged seat bottoms and backs

Engines, Trailer & Navigation System:
Main Motor: Mercury 150HP EXLPT EFI 4-Stroke - 25in Shaft, Power Trim
Trailer: All Welded D-Tube Aluminum Guardian trailer with UHMW bunks and side guides
Navigation System: Lowrance HDS-7 Carbon Ultra-Clear SolarMAX™ HD display

Included Factory Options:
Hull Color 1: Silver Vein Dark Grey Powder Coat with Gloss Clear Second Layer Powder Coat (Upgrade)
• Hull Color 2: Metal Flake Dark Grey HD 3M Vinyl
• Power assist steering
• 2 deluxe River Master seats w/fold up arms on pedestals
• Powder coat interior and welded frame top upgrade
• 2 - 18'X32" storage box seats with cushion
• Stainless steel bow and side railing
• 1/2 top with side curtains and drop curtain and zip up door
• Spare tire, wheel, and mount to trailer
• Wash down pump system with transom scoop

High End Trailer Features:
Custom D-Tube Aluminum Guardian Trailer
• All welded , nothing is bolted
• with UHMW (Ultra High Molecular Weight Polyethylene) bunks and side guides
• 15" tires and wheels with galvanized rims
• Dual wheel tongue jack, Winch, Torsion Axle
• Disc brakes
• LED lights
Vault oil bath hubs

Additional Equipment:
• Upgrade to UFLEX Hydraulic Steering
• SmartCraft Tachometer Gauge
• Rigging Hose Kit
• Stainless Steel Enertia Propeller
• Panel Mount Remote Control
• Premium Control Cables
• Dashboard Mount Key Switch
• Sharkhide Trailer Protectant
• Bentley Mariner Heavy Duty Swivels for Suspension Seats
• Transom Fish Box

Additional Services & Costs:
Pre Delivery Inspection & Freight: $1,500.00

Hull Warranty to original purchasers:
• 10 Years for Commercial Users
• Lifetime for Private Users

The RPM Group is the exclusive Dealership for Rogue Boatworks in Canada!


Alberni Power & Marine, Rod’s Power & Marine Ltd. and Alberni Industrial Marine Supply Ltd., to be referred as RPM Group is not responsible for, and expressly disclaims all liability for, damages of any kind arising out of use, reference to, or reliance on any information contained within the website, while the information contained within the site is periodically updated no guarantee is given that the information provided in this website is correct, complete, and up-to-date.

Product information is based on material received from suppliers. RPM Group is very eager to provide to all clients a verification of its website content.

Request Custom Quote Request More Info Print Page